MOISTURE METERS
Spare parts are available for all Logica H&S production products, from the single screw to the more complex electronic board.
For the latter, a technical assistance service is also available that can repair the boards (not just replace them!), Guaranteeing comparable service costs (often free of charge).
In urgent cases, it can be agreed to send a replacement card, new or restored, simultaneously with the shipment of the card to be repaired by the customer, guaranteeing an extremely limited period of downtime anywhere in the world.

UR/T SENSOR
The UR/T sensor allows you to use your LG43 meter for measuring ambient humidity. In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balance humidity (EMC).
The accurate shielding of the sensor also makes it ideal for use inside the kiln dryer.
Compatibility: LG43
Code: C001553

UR/T SENSOR
The sensor allows you to use your MoisTxxx meter for measuring ambient humidity. In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balance humidity (EMC). The accurate shielding of the sensor also makes it ideal for use inside the drying kiln.
Compatibility: MoisTrue, MT10, MT20, MT30
Code: C002836

UR PROBE FOR CONCRETE FLOORS
This accessory is suitable for use with the items described above, to measure the relative humidity in concrete floors in compliance with ASTM F2170. The probe (Ø 10mm) inserted in the aluminum seat ensures an excellent seal guaranteeing reliable measurements.
Compatibility: LG43
Code: C002103

HOLE LINERS FOR CONCRETE FLOORS
These elements are provided with a plug and a sliding gasket (to adapt perfectly to the depth of the hole) and have two deformable gaskets to seal the holes in which the moisture detection probes will subsequently be positioned.
The diameter of the hole required for their insertion is 14 mm.
Compatibility:
Code: C002100 - aluminum seat length. 50mm
C002101 - aluminum seat length. 100mm

RH/T/EMC SENSOR
Accessory for MoisTrue/MoisTest for estimating the moisture of sawdust or wood chips, particularly suitable for values lower than 20%. Connected to compatible meters, it must be inserted deep into the material to be measured.
Stainless steel probe - length 30cm - Ø8mm
Compatibility: MoisTrue, MT10, MT20, MT30
Code: C002989

SPF PROBE FOR SAWING MEASUREMENT
Accessory for resistance meter for estimating moisture of sawdust or wood chips, particularly suitable for values higher than 15%.
Connected in place of the normal electrode holder, it must be inserted deep into the material to be measured, suitably compacted.
SPF AISI304 probe - length 60cm - Ø12mm
Compatibility: MoisTrue / LG43
Code: C001909

TEST BOX FOR PIN-TYPE METERS CALIBRATION CHECK
Compatibility: MoisTrue / LG43 + all Pin-Type compatible control systems
Code:C001578 - (11.5% 25 ° C - Group 3)
Code:C000910 - (18.5% 25 ° C - Group 3)
Code:C000911 - (32.5% 25 ° C - Group 3)

TEST BOX FOR CONTACT METERS CALIBRATION CHECK
Compatibility: MT10, MT20, MT30
Code: C003094

CONDUCTIVE RUBBER ELECTRODES FOR SURFACE MEASUREMENTS
Pair of AISI303 stainless steel electrodes fitted with conductive rubber for surface measurements.
These items do not damage the measured material in any way.
They are used with the Plastic Handle, simply by screwing them onto the instrument instead of electrodes.
Compatibility: LG43 / MoisTrue + Plastic Handle
Code: C001432

INSULATED ELECTRODES
Compatible with our Pin-Type meters, they are made of treated steel. These electrodes have an extremely sharp tip that allows easy measurements even in depth.
INSULATED VERSION: The insulated stem allows the measurement of the correct in-depth moisture of the wood even in the presence of a moist surface layer (e.g. frost)
Two different lengths are available in the catalog and can be used with the electrode Hammer or Plastic Handle.
Compatibility: MoisTrue / LG43
Code: C001945- 20pcs x 25mm
Code: C001946-20pcs x 40mm
Code: C002679- ASSORTED SET 20pcs (10 x 25mm + 10 x 40mm)

NOT INSULATED ELECTRODES
Compatible with our Pin-Type meters, they are made of treated steel. These electrodes have an extremely sharp tip that allows easy measurements even in depth.
NOT INSULATED VERSION: They can be used instead of the insulated ones in all cases where there is no wetter layer on the surface, guaranteeing savings on the purchase price and greater strength.
Two different lengths are available in the catalog and can be used with the electrode Hammer or Plastic Handle.
Compatibility: MoisTrue / LG43
Code: C002345- ASSORTED SET 20pcs (10 x 25mm + 10 x 40mm)
Code: C002346- 20pcs x 25mm
Code: C002347-20pcs x 40mm

PERFORATION ELECTRODES FOR SURFACE MEASUREMENTS
Turned steel electrodes with very short (0.5mm) and sharp tip, suitable for measurements on thin materials (veneers, paper, leather) or for surface measurements.The short and sharp tip allows non-intrusive measurements in the materials, leaving almost imperceptible marks.Particularly suitable for use with Plastic Handle, they can also be installed on the electrode Hammer.
Compatibility: MoisTrue / LG43
Code: C000548

CONNECTION CABLE FOR
HAMMER AND PLASTIC HANDLE
Connection cable made with highly insulated cables and connectors, allows you to connect Handler or Hammer to the moisture meter ensuring reliable measurements.
Compatibility: MoisTrue / LG43
Code: C000102

PLASTIC HANDLE FOR SURFACE MEASUREMENTS
Accessory for Pin-Type meters, consisting of a practical high-insulation handle and a series of turned steel electrodes with a thin tip and a penetration depth of 0.5mm. Useful for surface measurements on veneers or non-wood materials. It can also accommodate standard 40 or 60 mm electrodes.
Compatibility: MoisTrue / LG43
Code: C000095- 20pcs x 25mm

ELECTRODE HOLDER HAMMER
PER MEASURES IN DEPTH
Accessory for Pin-Type meters, consisting of a powder-coated metal part with striking mass from a head in highly insulated plastic material.
The striking mass allows an easy insertion (and extraction) of the electrodes in the material to be measured.
Weight: 1.5kg
Compatibility: MoisTrue / LG43
Code: C001626

SPARE HEAD FOR HAMMER
If the plastic section of the hammer C001626 is damaged, only the damaged part can be replaced.
This particular must necessarily be made of highly insulated plastic material, therefore it is more fragile than the remaining parts of the accessory. It is however possible to ensure a very long life by simply avoiding tightening the electrode locking nuts too hard and drilling guide holes for measurements on particularly hard materials or at very great depths.
Compatibility: MoisTrue / LG43
Code: C000584

BIOMASS METER
The biomass moisture measurement accessory can be used for an easy measurement of the moisture content in wood sawdust or, more generally, in all fine-grained biomasses. The gun allows you to compress the material to be measured in an easy and repeatable way, ensuring fast and accurate readings.
Caution: The accessory set does not include the measuring tool.
Find out more:https://www.logica-hs.it/biomassmeter
Compatibility: MoisTrue / LG43
Code: C003074