Accessories and spare parts for moisture meters

accessories and spare parts

Of course, we can supply the spare parts for all instruments produced by LogicaH&S, from the single screw to the most upgraded electronic board.

As for boards, we can also supply customers with our technical assistance which is able to repair (and not only to replace!) electronic boards: in this way we can guarantee very low assistance costs (often assistance is free!).

feeler pin for surface readings

Accessory for pin type meters mod. LG43, which consists of a practical high insulation handle and a series of steel-turned electrodes with sharp pins and penetration depth of 0,5mm. It is used for surface readings on veneers and other materials (not wood). This feeler pin can also contain standard electrodes (40 or 60 mm.).

CODE: C000095

Electrode hammer for deep readings

Accessory for pin type meter mod. LG43, which consists of a painted metal part with a high insulation plastic head.

 

The high weight mobile mass allows electrodes to be easily pushed into / taken from the tested material.

CODE: C001626 - Weight 1,5 kg approx

spare hammer head

In case of damage on the plastic section of the hammer C001626, you are able to replace only the damaged part. The head is necessarily made of high insulation plastic material: for this reason, this part is more fragile than other parts of the hammer.

A long-time use can be guaranteed simply by avoiding to tighten electrodes-blocking nuts with too much force and by making driving holes when testing on very hard materials or in the deepest.

 

CODE: C000584

Connection cable for hammer / Feeler pin

Connection cable, made with high insulation cables and connectors, which can be used to connect the feeler pin or hammer with the instrument LG43 and to guarantee good readings.

CODE: C000102

Insulated electrodes for deep readings

Stainless steel insulated electrodes with a very sharp pin, which are suitable for good readings in depth with an instrument LG43.


They are available in three different lengths and can be used with electrodes hammer and feeler pin.


Code C001944 - ASSORTED (nr. 18 electrodes (nr.6 x leng.  25/40/60mm))
Code C001945 - SET 25 (nr.20 electrodes da 25mm)
Code C001946 - SET 40 (nr.20 electrodes da 40mm)
Code C001947 - SET 60 (nr.20 electrodes da 60mm)

Pin type electrodes for surface readings

Stainless steel turned electrodes with a very short (0,5mm) and sharp pin, suitable for readings on thin materials (veneers, paper, leather) or for surface readings.

The short and sharp pin allows to make non-intrusive readings on materials, leaving almost imperceptible traces on it.


They are very suitable for the use on a feeler pin buth can also be installed on an electrode hammer.

 

CODE: C000548

Touch type conductive rubber electrodes

AISI303 stainless steel electrodes with a conductive rubber for non-intrusive surface measurement.

They can be fixed on the feeler instead of the normal pins.

 

CODE: C001432

Test Box for moisture meters calibration

C001578 Test Box for resistance moisture meters (11,5% 25°C Gr. 3)


C000910 Test Box for resistance moisture meters (18,5% 25°C Gr. 3)


C000911 Test Box for resistance moisture meters (32,5% 25°C Gr. 3)

SPF probe

It is an accessory for resistance meters, useful to estimate the moisture content of sawdust or wood shavings.

 

Connected instead of the electrode holders, it must be inserted deeply into the material to be measured, which has to be properly compacted.

CODICE: C001909 - SPF AISI304 - length 60cm - Ø12mm

RH/T/EMC sensor for LG51/LG52

Measures temperature, relative humidity and equilibrium humidity. It is particularly suitable for measuring the humidity (0-20%) of sawdust, wood chips and wood materials in general.

 

CODE: C002989 - Stainless steel rod 30cm - 1m cable

Aluminum seat for holes in concrete floors

These elements are equipped with a cap and a sliding gasket (to perfectly adapt to the depth of the hole) and have two deformable gaskets to seal the holes in which the humidity detection probes will subsequently be positioned.

 

The diameter of the hole required for their insertion is 14 mm.

 

C002100 aluminum seat L = 50mm
C002101 aluminum seat L = 100mm

Relative humidity probe for concrete floors

This accessory for the LG43 instrument is suitable for use with the items described above, to measure relative humidity in concrete floors in compliance with ASTM F2170.

 

The probe (Ø 10mm) inserted in the aluminum seat ensures an excellent seal guaranteeing reliable measurements.

 

Code C002103

Relative Humidity / Temperature sensor for Moist XXXX series instruments

The C002836 sensor allows you to use your MoisTest or MoisTrue meter to measure ambient humidity.

 

In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balancing humidity (EMC). The accurate shielding of the sensor also makes it ideal for use inside the drying oven.

Relative humidity / temperature sensor for LG43 series instruments

The C001553 sensor allows you to use your LG43 meter to measure ambient humidity.

 

In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balancing humidity (EMC).

 

The accurate shielding of the sensor also makes it ideal for use inside the drying oven.