Accessories and spare parts for kiln dryers

accessories and spare parts

Of course, we can supply the spare parts for all instruments produced by LogicaH&S, from the single screw to the most upgraded electronic board.

 

As for boards, we can also supply customers with our technical assistance which is able to repair (and not only to replace!) electronic boards: in this way we can guarantee very low assistance costs (often assistance is free!). In case of emergency, we can supply, in accordance with customers, a replacing board (a new or restored one) while the customer sends us back the damaged one, to assure a very short interruption of machine working in all over the world.

electrodes holder

Lightweight and compact size electrodes holder (Ø45X16mm), POM made, with two stainless steel electrodes (length 15mm) that can be used manually to detect moisture in soft materials, like paper tubes or something similar. It is provided with silicone insulated cable and Banana plugs.

 

CODE: C001955 - Electrode holder with two stainless steel electrodes, banana plugs, silicone insulated cable - length 5m *


CODE: C001954 - Electrode holder with two stainless steel electrodes, banana plugs, silicone insulated cable - length 10m *

 

* Other cable lengths available on request

Spare parts for electrodes holder

AISI304 stainless steel elettrodes, point 15x2,5mm and M6 thread, suitable with Electrodes holder

CODE: C002040

* Sold in packs of 10

Electrodes for moisture measurement

Series of AISI303 stainless steel electrodes provided with Ø 4 mm hole for banana plugs, suitable for timber moisture testing.
For a long-time duration, we suggest to make a driving hole of a diameter slightly smaller than the electrode's (4 mm) to make its placement easy. (The driving hole must be made with low rotations drill, to prevent wood from heating).


Lenght 15 mm * - CODE: C000009
Lenght 25 mm * - CODE: C000010
Lenght 40 mm * - CODE: C000011

* Sold in packs of 20

Electrodes for moisture measurement

Series of AISI304 stainless steel electrodes provided with a Ø 4 mm hole for banana plugs, suitable for timber moisture testing.
This electrodes can be easily placed/removed using a standard screwdriver thanks to its threaded tip.


Lenght 15 mm * - CODE: C001484
Lenght 25 mm * - CODE: C001485
Lenght 40 mm * - CODE: C001486

* Sold in packs of 20

Banana plugs

Connectors made of AISI304 stainless steel, Ø 4 mm, with rubber insulation, suitable for high temperature into the kiln. They can be supplied as spare parts for timber probe cables.


CODE: C001483

cellulose plates

Cellulose plates for the equilibrium moisture measurement inside the chamber. They correspond exactly to the calibrations required by our controllers.
WARNING: the characteristics of cellulose are different for every producer; it is strongly recommended to use original spare parts only.

Pack 50 pcs - CODE: C000498
Pack 100 pcs - CODE: C000499

High-performance cellulose plates

Cellulose plates for the equilibrium moisture measurement inside the chamber. They correspond exactly to the calibrations required by Logica controllers. Compared to the traditional version, these plates offer an improved sensitivity to low EMC values and an higher reliability, thanks to the printed contact strips.


WARNING: the characteristics of cellulose are compatible with Delphi and dTOUCH control systems only; for the less recent Delphi (version < 5.1) a firmware upgrade is recommended.

Confezione 50 pz - CODICE: C001587
Confezione 100 pz - CODICE: C001588

probe panels

To guarantee controller's good working, probe panels and cables inside the kiln must always be in perfect state: dust or damage can affect electrical insulation and may cause wrong readings.
As spare parts, we can also supply panels provided with temperature probe (NTC) and cellulose clamp, with 3 or 6 connectors for probe cables or with direct output of 2 or 4 probe cables.
Panels are provided with high insulation cable (Teflon®) to be connected with the amplifier (available length: from 5 to 30m—multiple of 5m).

Probe cables

Like probe panels, cables for timber probes must always work in perfect conditions.

Damaged or deteriorated cables cannot be repaired (a normal insulator cannot guarantee a good insulation) and must be immediately replaced. We can supply silicon or Teflon® insulated cables, shielded or unshielded, with single or double banana plugs termination.

Length from 5 to 30m (multiple of 5m)

Aluminum probes box for conventional cycles

Is now available on request, a new line of resistant aluminum probes box, with special PTFE parts to ensure an optimum electrical insulation.

These new products have been designed by LogicaH&S to be long lasting, and be employed in conventional cycles.

Aluminum probes box for HT (heat treatment) cycles

Is now available on request, a new line of resistant aluminum probes box, with special PTFE parts to ensure an optimum electrical insulation.
These new products have been designed by LogicaH&S to be long lasting, and be employed in HT (heat treatment) cycles. 

Compact plate for probes box mounting

Compact plate made of stainless steel for fixing the probes box to the wall. It is a compact model that can be used in alterative to the traditional ones, that are more prominent due the overhead guard.

CODE: C001668